Go Back  The Hull Truth - Boating and Fishing Forum > BOATING FORUMS > SportFishing and Charters Forum
Reload this Page >

Ideas for a wall mounted fishing rod/reel holder

Notices

Ideas for a wall mounted fishing rod/reel holder

Old 11-12-2010, 06:18 AM
  #1  
Senior MemberCaptains Club Member
Thread Starter
 
Join Date: Nov 2006
Location: New Smyrna Beach
Posts: 8,681
Received 343 Likes on 233 Posts
Default Ideas for a wall mounted fishing rod/reel holder

Looking for ideas to build a wall mounted rod/reel holder that will hold 25+ rod/reels. I'm thinking the rod/reel rack will need to be so the rod/reels will be able to stand up vertically. Any pictures or thoughts on what you have done would be appreciated.
Old 11-13-2010, 05:11 AM
  #2  
Senior Member
 
Join Date: Jul 2005
Location: Wilmington NC
Posts: 4,189
Received 570 Likes on 282 Posts
Default

Here goes , I hang a few of my surf rods & jigging rods from the ceiling using rubber coated bicycle hooks
Light tackle set ups PVC pipe in a milk crate .............
Man this is an old picture, have a few more rods now, but still using the same setup ......... ICM
Attached Images   
Old 11-13-2010, 05:40 AM
  #3  
Senior MemberCaptains Club Member
 
Join Date: Aug 2005
Location: Angier NC
Posts: 443
Likes: 0
Received 0 Likes on 0 Posts
Default

This should keep you busy for awhile:

http://www.thehulltruth.com/sportfis...-part-2-a.html

http://www.thehulltruth.com/sportfis...ge-garage.html

http://www.thehulltruth.com/sportfis...l-storage.html

http://www.thehulltruth.com/sportfis...d-holders.html

http://www.thehulltruth.com/sportfis...d-storage.html

Ray
Old 11-14-2010, 04:58 AM
  #4  
Senior MemberCaptains Club Member
 
Join Date: Feb 2002
Posts: 1,400
Likes: 0
Received 11 Likes on 9 Posts
Default

This is not home built but it is one of the best ways I have stored rods.

http://www.rodsteward.net/products.html

I have no affiliation w/ them.

Old 11-14-2010, 06:04 AM
  #5  
Admirals ClubCaptains Club Member Admiral's Club Member
 
Join Date: Mar 2007
Location: Lighthouse Point
Posts: 5,634
Received 1,134 Likes on 747 Posts
Default

http://www.piranharodrack.com/

These work great I have two for 6 trolling rods and 8 spinners.

Joe
Old 11-15-2010, 01:10 PM
  #6  
Senior MemberCaptains Club Member
 
Join Date: Dec 2003
Location: Ft. Lauderdale, FL
Posts: 2,375
Received 90 Likes on 49 Posts
Default

right rigger - which model do you have?
Old 11-16-2010, 05:57 PM
  #7  
Senior MemberCaptains Club Member
 
Join Date: Feb 2002
Posts: 1,400
Likes: 0
Received 11 Likes on 9 Posts
Default

I think it was the large saltwater
Old 11-16-2010, 06:12 PM
  #8  
Admirals Club Admiral's Club Member
 
Join Date: Nov 2007
Location: Long Island, NY
Posts: 9,285
Received 813 Likes on 528 Posts
Default

Without knowing what king of rods, the simplest would be to take a pair of 2"x4"x16' long (you need to space offshore reels - Penn 70's or 50W's 8" apart (center to center), while Avet MX's will do with 6") and attach 1-1/2" pvc cut to 11" long lengths. It is a pretty simple design, which is then bolted to the wall. I have the same design in cube form, that holds 24 offshore rods & reels in a 38" long x 20" wide rectangle (6 per row), and a second that holds 20 inshore rods in a 24" x 16" rectangle (5 per row).
Old 11-16-2010, 06:33 PM
  #9  
Admirals Club Admiral's Club Member
 
Join Date: Nov 2009
Location: Deale, MD
Posts: 2,639
Received 1,131 Likes on 442 Posts
Default

Ran a 1 X 4 across the wall, screwed to the studs, screwed rodholders to the 1 X 4. Since this picture was taken, I have upgraded to Penn 330LD reels that will not fit in the 3 rod rodholders. I took down the 3 rod rodholders and have replaced them with AFI single rod rodholders spaced further apart.
Attached Images  
Old 11-17-2010, 05:22 AM
  #10  
Admirals Club Admiral's Club Member
 
Join Date: Nov 2007
Location: Long Island, NY
Posts: 9,285
Received 813 Likes on 528 Posts
Default

Originally Posted by Tawn View Post
Ran a 1 X 4 across the wall, screwed to the studs, screwed rodholders to the 1 X 4. Since this picture was taken, I have upgraded to Penn 330LD reels that will not fit in the 3 rod rodholders. I took down the 3 rod rodholders and have replaced them with AFI single rod rodholders spaced further apart.
That was exactly what I suggested, using individual 1.5" pvc pipe cut to 11" instead of the pre-made units. You get 10 rod holders out of a single 10' pipe that sells for $4, vs. $7 each for the AFI's. To make mine more rod friendly, I rout the inside lip of the sections with a 1/8"r router bit, then drill two 3/8" holes one 2" from the bottom and the second 1.5" from the top on one side, and then through those holes a rcess with that 3/8" bit and then a 3/16" hole for the screws.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.