Notices
 
Search: Posts Made By: mitchell master
Showing results 1 to 25 of 500
Search took 0.57 seconds.
09-13-2020, 02:01 PM
Replies: 1
Views: 166
Posted By mitchell master

Dwight D Eisenhower was president when that...

Dwight D Eisenhower was president when that engine was manufactured. You should start by checking compression,spark on both cylinders and fuel quality. As for the mixture screws,get it running and...
09-07-2020, 03:44 PM
Replies: 5
Views: 161
Posted By mitchell master

ONC key switch with lanyard ?

ONC key switch with lanyard ?
09-06-2020, 07:52 AM
Replies: 9
Views: 279
Posted By mitchell master

If it still runs hot after whatever you do,google...

If it still runs hot after whatever you do,google ''bravoitis''
09-04-2020, 02:08 PM
Replies: 23
Views: 418
Posted By mitchell master

Take all the old fuel lines off and check for...

Take all the old fuel lines off and check for collapsed inner liner. Eliminate the fuel connector on the side of the engine and go straight to the fuel pump. Also make sure the fuel/water separator...
Forum: Dockside Chat
09-04-2020, 06:58 AM
Replies: 29
Views: 1,819
Posted By mitchell master

Sounds like the county is looking for a cash cow...

Sounds like the county is looking for a cash cow or two.
Forum: Dockside Chat
09-03-2020, 07:11 PM
Replies: 164
Views: 12,391
Posted By mitchell master

https://cimg2.ibsrv.net/gimg/www.thehulltruth.com-...

https://cimg2.ibsrv.net/gimg/www.thehulltruth.com-vbulletin/960x640/falling_down_3_82ac3ddf3d853bce98ce1706a27df775fca574e6.jpg
09-02-2020, 01:48 PM
Replies: 11
Views: 1,107
Posted By mitchell master

You're going to have to get your head and phone...

You're going to have to get your head and phone in there and see what's worn.Look at the cable movement and steering yoke while someone moves the helm and drive.
09-01-2020, 04:37 PM
Replies: 10
Views: 333
Posted By mitchell master

When I went to thru hull exhaust on my volvo...

When I went to thru hull exhaust on my volvo drive in a speed boat back in the day,I removed the Y-pipe and made a alum. block off plate.
Forum: Dockside Chat
09-01-2020, 10:16 AM
Forum: Dockside Chat
09-01-2020, 09:55 AM
Replies: 36
Views: 973
Posted By mitchell master

Make sure it's not overheating from not enough...

Make sure it's not overheating from not enough oil.
09-01-2020, 08:31 AM
Replies: 6
Views: 288
Posted By mitchell master

The engine has to make a few revolutions for the...

The engine has to make a few revolutions for the computer to learn crank position.
09-01-2020, 05:50 AM
Replies: 14
Views: 393
Posted By mitchell master

If you want to use the non vro stock pump,use two...

If you want to use the non vro stock pump,use two in series.One will not keep up.
08-31-2020, 03:37 PM
Replies: 11
Views: 385
Posted By mitchell master

''Overheat code'' Check the exhaust flappers.

''Overheat code'' Check the exhaust flappers.
Forum: Dockside Chat
08-30-2020, 07:19 PM
Replies: 26
Views: 1,909
Posted By mitchell master

Bread fruit.

Bread fruit.
08-30-2020, 02:52 PM
Replies: 14
Views: 324
Posted By mitchell master

Did you make sure the bearing actually fits the...

Did you make sure the bearing actually fits the drive shaft ?
Forum: Dockside Chat
08-30-2020, 11:11 AM
Replies: 23
Views: 2,254
Posted By mitchell master

He misspoke.They probably burned to the...

He misspoke.They probably burned to the ground,not broke down.
Forum: Dockside Chat
08-30-2020, 08:39 AM
Replies: 40
Views: 1,263
Posted By mitchell master

Caulk all the cracks,wet sponging while you...

Caulk all the cracks,wet sponging while you go,then paint it with Lanco roof sealer followed by color of choice.
08-29-2020, 02:49 PM
Replies: 10
Views: 223
Posted By mitchell master

Pull a couple spark plugs after trying to start...

Pull a couple spark plugs after trying to start it and see if they're wet or dry. Also make sure you're not trying to burn water.
08-28-2020, 03:22 PM
Replies: 6
Views: 193
Posted By mitchell master

You should be able to get a regulator with gauge...

You should be able to get a regulator with gauge on ebay for around 20.00
08-28-2020, 08:44 AM
Replies: 20
Views: 461
Posted By mitchell master

Put the back bolts back in loose just to square...

Put the back bolts back in loose just to square it up,put a smaller dia socket on top of the forward two nuts loosen them and use them to push the lower down.
08-26-2020, 07:43 PM
Replies: 16
Views: 722
Posted By mitchell master

To check for taper,use a feeler gauge and a...

To check for taper,use a feeler gauge and a piston ring to measure the bore at the top and bottom.
08-26-2020, 07:40 AM
Replies: 16
Views: 722
Posted By mitchell master

Take it somewhere else and have them measure the...

Take it somewhere else and have them measure the bores and compare them to Wiseco specs.
08-26-2020, 07:11 AM
Replies: 24
Views: 891
Posted By mitchell master

It will never be cost effective unless you find a...

It will never be cost effective unless you find a good used pivot assy. and do the work yourself.
08-26-2020, 06:15 AM
Replies: 24
Views: 891
Posted By mitchell master

Reading comprehension is not strong in this...

Reading comprehension is not strong in this thread.
Find a used pivot off a blown outboard and swap it.
08-25-2020, 07:00 PM
Replies: 27
Views: 581
Posted By mitchell master

It starts up easy when cold because all the...

It starts up easy when cold because all the leaked fuel has evaporated.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.