The Hull Truth - Boating and Fishing Forum - Search Results

Notices
 
Search: Posts Made By: scallen2112
Showing results 1 to 25 of 468
Search took 0.21 seconds.
06-25-2020, 04:33 AM
Replies: 11
Views: 541
Posted By scallen2112

No Holes ...

No Holes

https://cimg8.ibsrv.net/gimg/www.thehulltruth.com-vbulletin/640x480/transom_wedge_outer_38b6ff3df7996ab0b143a55c43555cc8a6ca082f.jpg...
06-24-2020, 06:29 AM
Replies: 11
Views: 541
Posted By scallen2112

I did it all at once and used my core to flatten...

I did it all at once and used my core to flatten the transom. I used two layers of 3/4 ply with 3 layers of glass between the plies an pre-built that part on a table so it was flat. When I put it in,...
06-22-2020, 11:45 AM
Replies: 8
Views: 670
Posted By scallen2112

Yeah, that's been the thing with the epoxy for me...

Yeah, that's been the thing with the epoxy for me - that I was hoping to cure to a point with poly. But, if I am going to be grinding anyway, like I am now, when I get back on it next weekend, then I...
06-22-2020, 11:19 AM
Replies: 8
Views: 670
Posted By scallen2112

So you're saying that with a gel time of, say, 12...

So you're saying that with a gel time of, say, 12 min in high 80s weather, that I should get the new layer down within the next four hours or forget it? So what do you do with poly when you come back...
06-22-2020, 05:54 AM
Replies: 8
Views: 670
Posted By scallen2112

This would essentially be a fresh start. I have...

This would essentially be a fresh start. I have the transom in and the first large bulkhead that forms the front of the bilge and two large flotation boxes that will be filled with foam and sealed....
06-21-2020, 07:42 AM
Replies: 8
Views: 670
Posted By scallen2112

Switch to Poly?

About to get back into my boat project after nearly a year away. I am at a place where switching from Epoxy to Polyester would be doable, but I know very little about working with poly. One of the...
06-07-2020, 09:04 AM
Replies: 19
Views: 667
Posted By scallen2112

To me, a bay boat is something I can get across...

To me, a bay boat is something I can get across open water to fish skinny water. First, it has to be able to handle 2-3' chop to get across the bay. After that, it needs to be able to get along the...
06-07-2020, 08:54 AM
Replies: 10
Views: 310
Posted By scallen2112

Who has time to clean the boat with using it so...

Who has time to clean the boat with using it so much? What could be more socially distanced than out on the water with no one else around?
04-09-2020, 11:02 AM
Replies: 23
Views: 2,057
Posted By scallen2112

A row of biscuits to line it up is all you really...

A row of biscuits to line it up is all you really need. A good glue joint is stronger than the wood around it anyway. Use tightbond 3, polyurathane (Gorrila Glue), or expoxy.
04-04-2020, 02:22 PM
Replies: 0
Views: 160
Posted By scallen2112

Tracker Panfish Rewire

Hey all - Before I order the new wire, connectors, panel, and pumps to rewire my 16' Tracker Panfish, does anyone see any problems with these sizes or setup? Thanks.

...
02-24-2020, 10:48 AM
Replies: 39
Views: 2,389
Posted By scallen2112

I started a full rebuild in epoxy. Aside from...

I started a full rebuild in epoxy. Aside from cost, the one thing I don't like is that I am constantly having to prep. I work on a piece of the boat this weekend, it cures, and I have to go back and...
02-18-2020, 07:44 AM
Replies: 10
Views: 898
Posted By scallen2112

Cool!...$4,800 with my choice of motor? :grin:

Cool!...$4,800 with my choice of motor? :grin:
02-18-2020, 07:21 AM
Replies: 10
Views: 898
Posted By scallen2112

Don't know about the fuel tank; I have not seen...

Don't know about the fuel tank; I have not seen the boat yet. Still trying to decide which way to go. I have a Tracker Panfish 16 that I use back in the creeks, but in the three years I have been...
02-17-2020, 02:55 PM
Replies: 10
Views: 898
Posted By scallen2112

So that is a Cape Horn? Reason I asked is that I...

So that is a Cape Horn? Reason I asked is that I found a 2013 for sale, but it is deeper and a 2 piece instead of a 3 piece. So was wondering if the older were 3 pieces like this.
02-17-2020, 01:23 PM
Replies: 10
Views: 898
Posted By scallen2112

Cape Horn 17 ?

Hey all. Saw this boat available. Ad says it has been "Completely redone". Assuming that means it has been stripped and repainted and any structural problems taken care of. Ad says it's a Cape Horn...
01-29-2020, 02:45 PM
Replies: 1
Views: 1,258
Posted By scallen2112

Bump

Bump
01-17-2020, 04:00 PM
Replies: 1
Views: 1,258
Posted By scallen2112

1987 Hydra Sports 2500 Walk Around - $14,000

!! NO LONGER FOR SALE !!

I have an '87 Hydra Sports 2500 WA for sale in Brunswick GA. The boat is in sound physical condition, not too bad cosmetically. It has twin 2006 Honda BF150 with 250 and...
07-30-2019, 01:27 PM
Replies: 13
Views: 2,552
Posted By scallen2112

His Dad's a TV repairman. He;s got this awesome...

His Dad's a TV repairman. He;s got this awesome set of tools. He can fix it.
07-30-2019, 12:49 PM
Replies: 391
Views: 101,774
Posted By scallen2112

Yeah, I happened to have a large chunk of my...

Yeah, I happened to have a large chunk of my assets liquid on 9/11. I dumped nearly a 1/4 mil into a few companies stock - mostly Home Depot - and racked up almost 300K in 9 months as everything came...
07-29-2019, 06:37 AM
Replies: 0
Views: 3,236
Posted By scallen2112

Four. The answer is "four" - because ice cream...

Four. The answer is "four" - because ice cream has no bones.
07-27-2019, 09:35 AM
Replies: 391
Views: 101,774
Posted By scallen2112

Easy - I bought boats I could afford.

Easy - I bought boats I could afford.
07-25-2019, 04:41 PM
Replies: 72
Views: 7,651
Posted By scallen2112

Uhm.....gotta ask: If it's designed for a jet,why...

Uhm.....gotta ask: If it's designed for a jet,why the prop? Seems like you're losing something there.
07-25-2019, 04:20 PM
Replies: 12
Views: 1,255
Posted By scallen2112

The number of threads on the subject has already...

The number of threads on the subject has already been mentioned on the other threads. Way to be redundant.
07-25-2019, 07:22 AM
Replies: 72
Views: 7,651
Posted By scallen2112

Not only is your Crestliner nearly twice as heavy...

Not only is your Crestliner nearly twice as heavy (2800 v the OP's 1415 or so with that engine) but it is also half again as wide. Makes a difference.
07-24-2019, 10:53 AM
Replies: 72
Views: 7,651
Posted By scallen2112

15x21 , 15-1/8x20, 15-1/4x19

15x21 , 15-1/8x20, 15-1/4x19
Showing results 1 to 25 of 468
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.