Notices
Search: Posts Made By: fsrtwo
Showing results 1 to 21 of 21
Search took 0.02 seconds.
Replies: 2
Views: 282
Posted By fsrtwo

Thanks Mike! Thanks Mike! I had and...

Thanks Mike!

Thanks Mike!

I had and interesting day on the water yesterday. I saw 6150 RPM and 42.6 with a half tank fuel and 2 people. I would usually only see 5650 RPM max.

I did run on a...
Replies: 2
Views: 282
Posted By fsrtwo

19' 250ss Making Oil & Oil on the Breather tube

I have a 250ss with 27 hours. I noticed the oil level has gone from halfway between low and high to the high mark on the dipstick since I did the 20 hour service. Is this normal?

Plus, I checked...
09-08-2020, 10:29 PM
Replies: 17
Views: 339
Posted By fsrtwo

I would buy a clamp on ammeter. Put it on the...

I would buy a clamp on ammeter. Put it on the battery cable. Start pulling fuses until the reading drops low.
09-03-2020, 06:57 AM
Replies: 1
Views: 241
Posted By fsrtwo

Cover for Pontoon

I am in need of a boat cover for my 2019 Crest Continental 250 SLS. Thanks!
Replies: 5
Views: 215
Posted By fsrtwo

So if I go from a 15 1/4x19 to a 15 3/8 x18, I...

So if I go from a 15 1/4x19 to a 15 3/8 x18, I would probably net the same top speed at the new WOT RPM? I am guessing I would have more power with a full boat?

The prop game is new to me... Is...
Replies: 5
Views: 215
Posted By fsrtwo

That was with a half tank and two people...

That was with a half tank and two people...
Replies: 107
Views: 13,888
Posted By fsrtwo

I just installed an "Engine Gateway Connect, V...

I just installed an "Engine Gateway Connect, V 1.0.0" to my Simrad G07 today. It too shows "2007 and older" as the outboard year, the motor is a 2019. I changed it to 2015 (the newest it would let...
Replies: 5
Views: 215
Posted By fsrtwo

DF250SS TL Prop Pitch Question

I have a new 2019 Crest Pontoon boat. It came with a DF250SS with a 15 1/4 x 19 SS prop.

I recently connected the motor to my Simrad and now have a more accurate Tach. I noticed that my max RPM is...
07-25-2020, 09:27 PM
Replies: 3
Views: 295
Posted By fsrtwo

Suzuki DF250SS 20 hr Oil Change w/Pump

I am about to hit 20 hours on my DF250SS. It's time for the first oil change.

Has anybody done an in water oil change with an extraction pump? Does it matter if the motor is tilted up or trimmed...
07-18-2020, 08:58 AM
Replies: 9
Views: 410
Posted By fsrtwo

Thanks for the insight. Are there any other...

Thanks for the insight.

Are there any other real life results anybody can share?
07-15-2020, 07:16 PM
Replies: 9
Views: 410
Posted By fsrtwo

Pontoon Bottom Paint Interval

I just purchased a new 25' Crest Tritoon. I haven't had a pontoon in ten years. I remember I had an old guy pull it for me every year and clean and touch up the paint. Well, now I'm the old guy and I...
06-29-2020, 11:08 PM
Replies: 7
Views: 419
Posted By fsrtwo

The link you provided from Brown's is the cable I...

The link you provided from Brown's is the cable I am referring to. It has 12v power, I am asking if it is switched 12v power.

The gateway that I am referring to is :

THT will not let me post a...
06-29-2020, 09:13 PM
Replies: 7
Views: 419
Posted By fsrtwo

Its a DF300AP, 2020

Its a DF300AP, 2020
06-29-2020, 04:58 PM
Replies: 7
Views: 419
Posted By fsrtwo

Well....nothing like answering your own question....

Well....nothing like answering your own question. I found the answer by searching to sticky thread and not the forum.

It looks like that is a trim signal input from an analog motor and not and...
06-29-2020, 02:19 PM
Replies: 7
Views: 419
Posted By fsrtwo

BTW, I just saw another thread that says there is...

BTW, I just saw another thread that says there is a Engine Gateway Connect instead of a Engine Interface cable. Since I have a GO7, this might be better than using a C10 gauge. I would still like to...
06-29-2020, 01:59 PM
Replies: 7
Views: 419
Posted By fsrtwo

Suzuki Engine Interface Cable Trim Connector

Has anybody had success in using the trim connector on the engine interface cable? I am planning a digital motor upgrade and would like to keep my analog trim gauge if possible. I will have a C10...
Replies: 1
Views: 396
Posted By fsrtwo

Suzuki DF250SSTL Vs 300AP

I am looking at a boat that is wired for a Suzuki DF250. I am thinking I would like a 300AP instead. I am not sure the dealer has the knowledge to do the conversion. So, I am thinking of doing the...
06-22-2020, 08:32 AM
Replies: 0
Views: 177
Posted By fsrtwo

Suzuki 250DF vs 300AP on a Pontoon

I am looking at 25ft tritoons. I have noticed they either have a 250DF or a 300AP. I have seen plenty of post comparing the two. I am curious with the addition of additional electronics on the "AP"...
06-17-2020, 08:55 AM
Replies: 7
Views: 343
Posted By fsrtwo

Thanks!, That's good info. I will get back to you...

Thanks!, That's good info. I will get back to you on the results.

Also, does the Simrad version do everything that the Suzuki version does? I am curious about engine faults!
06-15-2020, 07:15 AM
Replies: 7
Views: 343
Posted By fsrtwo

I would think that the gauge has a memory and...

I would think that the gauge has a memory and hold it since the gauges power off when the ignition shuts off.
06-14-2020, 09:57 PM
Replies: 7
Views: 343
Posted By fsrtwo

Suzuki Digital Gauge Metric/Standard

My fiend has a 2017 Suzuki 250 Outboard on his deck boat. Whenever he turns on the ignition, he has to set the gauge form Metric to US Standard again. Are these gauges meant to remember their...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.