The Hull Truth - Boating and Fishing Forum - Search Results

Notices
 
Search: Posts Made By: Outboard Specialties
Showing results 1 to 25 of 500
Search took 0.37 seconds.
Replies: 8
Views: 175

There you go, glad you found it.

There you go, glad you found it.
Replies: 8
Views: 175

I would look at the main harness plugs, square...

I would look at the main harness plugs, square brown plugs at transom area and under console, you might have some corrosion causing a short. With the key on you are energizing the trim down wire.
Replies: 8
Views: 175

It sounds like you have a bad trim switch on...

It sounds like you have a bad trim switch on binnacle or start/stop panel. The trim all runs through the start/stop panel so you need to isolate the binnacle as well to see if it follows.
Replies: 12
Views: 365

You can draw the oil out through the dip stick...

You can draw the oil out through the dip stick but it is not ideal because it doesn't get the gunk that builds up in the bottom. I would not do it this way all the time but every other time maybe. ...
06-29-2020, 10:47 AM
Replies: 5
Views: 461

Here is the 28 with single 300 zuke. He is very...

Here is the 28 with single 300 zuke. He is very happy with it.

https://www.thehulltruth.com/boating-forum/623788-new-build-whitewater-28-new-numbers-break.html
Replies: 2
Views: 165

If you hear the trim motor running then i would...

If you hear the trim motor running then i would think the relay and motor should be good. If the motor is stuck all the way up then maybe the tilt bracket is down preventing the down movement or...
06-27-2020, 04:47 AM
Replies: 2
Views: 160

what is the model/serial number? I can look up...

what is the model/serial number? I can look up for you.
Replies: 4
Views: 194

I agree check engine height first then figure out...

I agree check engine height first then figure out a prop. You should be able to spin the 15x19. The zukes like to run the 16" diameter props, I would have used a 16x17 or 16x18.5 to start.
Replies: 1
Views: 216

The 250ss only comes mechanical controls and the...

The 250ss only comes mechanical controls and the 300 only comes digital so none of the rigging is compatible, everything would need to be changed out. The 300 also only handles digital gauges which...
Replies: 10
Views: 254

The old 4 blade zuke props were 15" diameter,...

The old 4 blade zuke props were 15" diameter, newer ones are 15.25". It sounds like you have the right rpms and being a step hull is probably why they ended up with 4 blades. You can always tweak a...
Replies: 4
Views: 202

All those issues you found are possible causes to...

All those issues you found are possible causes to your alarms, all these new motors are voltage sensitive and need good clean power. Hopefully this is solved, good troubleshooting so far.
Replies: 115
Views: 41,528

Is it set up for 20" or 25" transom now?

Is it set up for 20" or 25" transom now?
Replies: 4
Views: 160

The tee is part of the nmea 2000 network, each...

The tee is part of the nmea 2000 network, each device cable plugs into a black tee under the dash, we've seen bad ones cause voltage issues. If you only saw the alarm once then it could have been a...
Replies: 4
Views: 160

Your nmea 2000 network has low voltage, could be...

Your nmea 2000 network has low voltage, could be connections, bad tee, or battery issue.
Replies: 1
Views: 146

Either a specified trim/tilt fluid or atf.

Either a specified trim/tilt fluid or atf.
Replies: 1
Views: 197

If the motor was changed then yes it needed to be...

If the motor was changed then yes it needed to be recalibrated with the suzuki software so it is set up properly with the controls and boat control module. You can add the serial number in the gauge...
Replies: 5
Views: 323

I would start with having water in the filter,...

I would start with having water in the filter, you'll need to drain all the filters and vst on motor to make sure no water is in the rest of the system. I would then run off a portable tank with...
Replies: 1
Views: 228

Couple things could be going on. The motor...

Couple things could be going on.
The motor could have a bad neutral switch and the motor is limiting out at 3000 because it thinks it is still in neutral when it is not.
Or the prop that is on...
Replies: 3
Views: 193

all the latch pieces and parts can be reused, you...

all the latch pieces and parts can be reused, you only need to order the cover itself. Its easy to swap over.
06-10-2020, 11:20 AM
Replies: 14
Views: 1,112

Call/text Mike lund at 954-471-1300, he handles...

Call/text Mike lund at 954-471-1300, he handles our used inventory. I believe we just took a pr of 200 suzuki's in on trade.
05-30-2020, 06:46 AM
Replies: 1
Views: 183

The 140 is only available in gloss cool white or...

The 140 is only available in gloss cool white or gloss nebular black.
Replies: 3
Views: 683

pm sent

pm sent
Replies: 5
Views: 240

That little play is normal. Is it an aluminum...

That little play is normal. Is it an aluminum prop? Next would be to adjust shift linkage to favor fwd a little more, like 2 threads.
Replies: 115
Views: 41,528

Best is to call us on this situation, there is...

Best is to call us on this situation, there is many questions and possibilities that is better understood in a conversation. You can contact Trent directly at 954-663-6901, he is our resident cat...
Replies: 5
Views: 240

This might be throttle adjustment but also make...

This might be throttle adjustment but also make sure the prop is fully secure and tight. I have also seen where aluminum props chatter at dead idle because there is not enough load on it, the...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.