Notices
 
Search: Posts Made By: jrybicki
Showing results 1 to 25 of 89
Search took 0.05 seconds.
04-07-2019, 09:17 PM
Replies: 34
Views: 2,091
Posted By jrybicki

Hard to say since its happening to both motors....

Hard to say since its happening to both motors. Things I would try to rule out is idle timing advance set properly? Fuel/Water separator fresh? maybe the idle mixture screws are just a bit off from...
04-01-2019, 08:17 PM
Replies: 32
Views: 5,539
Posted By jrybicki

I rewired my 21' Sea Fox and also installed all...

I rewired my 21' Sea Fox and also installed all the extra goodies. It is well worth doing it yourself, even just for the learning experience but also the peace of mind knowing it was done right. I...
07-08-2018, 06:15 PM
Replies: 8
Views: 886
Posted By jrybicki

Well, I'm not having any luck finding a footmans...

Well, I'm not having any luck finding a footmans loop with the same measurements. I know they're out there since I have a plastic one that does fit, I just don't know who manufactured it or where it...
07-08-2018, 08:30 AM
Replies: 8
Views: 886
Posted By jrybicki

Jumpsummo, unfortunately strapworks doesn't have...

Jumpsummo, unfortunately strapworks doesn't have one that has the correct center to center measurement. The 2" Stainless are 2.95" and the plastic one they only have in a 1.5" footmans loop that...
07-07-2018, 01:17 PM
Replies: 8
Views: 886
Posted By jrybicki

Leaning Post cooler tie down

Since I bought my boat a few years ago it has had a missing footmans loop on the back of the leaning post for the cooler tie down. Went to west marine today and picked up some 2" footmans loops to...
07-17-2017, 09:47 AM
Replies: 76
Views: 16,513
Posted By jrybicki

I did not take pictures of the finished wiring...

I did not take pictures of the finished wiring because I still need to re work my auto pilot standby switch, I opted for a bocatech vs the provided switch and currently does not put ap in standby....
06-23-2017, 07:37 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Well pretty much finished with this project. Got...

Well pretty much finished with this project. Got the new stator and rectifier in and got most of the t top grommets in, the rest are too tight to fit so I'll have to come up with some other way of...
06-22-2017, 08:27 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Well I was able to get the bep 701md working...

Well I was able to get the bep 701md working right just had to change some wires around in the bocatech switch. I was also able to get the radar working, when I re crimped the rj45 I put it on upside...
06-22-2017, 03:19 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Got the anchor light from fishonsports.com and...

Got the anchor light from fishonsports.com and the wire labeler is a Brady bmp 21. It's a bit expensive but very rugged and easy to use. I used mostly self laminating wire labels with the exception...
06-22-2017, 09:28 AM
Replies: 76
Views: 16,513
Posted By jrybicki

Thanks for the reply bocatech! I've got it...

Thanks for the reply bocatech! I've got it figured out now I think. When I did the initial testing of the switch everything seemed to work right. I have it connected to my bep 701-md battery switch....
06-21-2017, 11:16 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Finally!! Super productive night after work...

Finally!! Super productive night after work finished around midnight... well at least the console. I still need to clean up the wires a bit nicer but it's good enough for now and everything is hooked...
06-20-2017, 07:18 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Successful evening after work today. I was able...

Successful evening after work today. I was able to get the rest of the wires untangled zip tied and re routed and hooked up. Looks much better and went a lot smoother. Should have done it that way to...
06-20-2017, 04:48 AM
Replies: 76
Views: 16,513
Posted By jrybicki

Thanks for your input. I think the virtual switch...

Thanks for your input. I think the virtual switch comes from the yellow wake wire connected to the hds but it still needs a separate power wire. The current plan is to terminate all the wake up lines...
06-19-2017, 07:43 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Surprise surprise today didn't go as planned,...

Surprise surprise today didn't go as planned, seems to be a common theme with this project. I spent a bit of time trying to keep all the wires separated into groups for where they'd get routed but...
06-18-2017, 10:04 PM
Replies: 76
Views: 16,513
Posted By jrybicki

I get what you're saying, I've done what I can to...

I get what you're saying, I've done what I can to minimize the chances of that happening hoping these ones will last a couple seasons.

I got the unidock really to use my old school iPod on the...
06-18-2017, 07:17 AM
Replies: 76
Views: 16,513
Posted By jrybicki

Umm yeah obviously didn't even look at page 1 or...

Umm yeah obviously didn't even look at page 1 or any of the wire diagrams. My bilge pump is connected manually as well as powered by a separate 24hr circuit with an ultra switch. As far as led lights...
06-17-2017, 08:48 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Back at it this weekend and of course it rained...

Back at it this weekend and of course it rained most of the day. I was still able to get a clam shell installed, the point 1 installed, the 701 remote cluster installed with all connecting wires, all...
06-04-2017, 08:38 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Another weekend down and still not done......

Another weekend down and still not done... Saturday I only worked on the boat for a few hours since I slept most of the day after the 15 hour drive back from MI.

I was able to get the 3d...
05-29-2017, 04:01 PM
Replies: 7
Views: 3,023
Posted By jrybicki

You're better off launching and tying off to a...

You're better off launching and tying off to a dock to adjust idle so you'll have back pressure on the exhaust. Otherwise no real time limitations on muffs as long as the flow is good and you don't...
05-28-2017, 06:33 PM
Replies: 76
Views: 16,513
Posted By jrybicki

I got the panel made at new wire marine. I...

I got the panel made at new wire marine. I measure everything off my old panel did a cad drawing to play around with how I wanted everything and sent it to them. They tweaked it a bit and we went...
05-27-2017, 07:38 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Again no pictures, also not even close to...

Again no pictures, also not even close to finished. I got all the mounting boards in with the fiberglass resin, that stuff is legit! Also finished building the wire harness. Installed the radar and...
05-26-2017, 11:38 PM
Replies: 76
Views: 16,513
Posted By jrybicki

More progress again today. I didn't take pictures...

More progress again today. I didn't take pictures as I was just bouncing around trying to knock out as much as I could.

Got the auto pilot steering unit, switch panel, helm e box installed. I got...
05-25-2017, 07:32 PM
Replies: 76
Views: 16,513
Posted By jrybicki

More progress today still hopeful to have this...

More progress today still hopeful to have this wrapped up Saturday evening so I can enjoy the rest of my vacation back home in Michigan with family for a week. Late last night I remembered that I had...
05-24-2017, 08:28 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Another productive day down, I think I'm still on...

Another productive day down, I think I'm still on track to have this wrapped up this weekend but I'm probably underestimating pulling and labeling the new wire. Happy with how much I got done today...
05-23-2017, 08:29 PM
Replies: 76
Views: 16,513
Posted By jrybicki

Today was fairly productive considering the rain...

Today was fairly productive considering the rain and thunderstorms all day. I started the day off with the rod lockers.

Marking out slots for the led lights
824646

Dremeled the slots out...
Showing results 1 to 25 of 89
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.