Notices
 
Search: Posts Made By: wstanford277
Showing results 1 to 25 of 500
Search took 0.19 seconds.
06-16-2021, 02:56 PM
Replies: 34
Views: 1,374
Posted By wstanford277

Go to a Suzuki dealer. Worst case your insurance...

Go to a Suzuki dealer. Worst case your insurance will pay (minus deductible) for “striking” an object.
06-15-2021, 06:25 PM
Replies: 10
Views: 522
Posted By wstanford277

2 years ago I followed this advice on my first...

2 years ago I followed this advice on my first trip to marathon- run a few miles into the gulf and find a sandy spot in 8-10ft of water. Anchor and drop a Drop a chum bag. Make a sandwich and start...
06-15-2021, 05:58 PM
Replies: 2
Views: 126
Posted By wstanford277

Use the existing wire to pull the new wire thru...

Use the existing wire to pull the new wire thru the hull. Lots of tape and silicone lubricant.
06-14-2021, 08:27 PM
Replies: 8
Views: 290
Posted By wstanford277

You could drill the 4 bolts out but you will need...

You could drill the 4 bolts out but you will need to remove the nuts and shavings from the anchor locker. If you know the size of the nut on the underside tape something (ex 24” pipe) to a socket...
06-14-2021, 02:06 PM
Replies: 2
Views: 105
Posted By wstanford277

Check the white cylinder fuel filter by the VRO...

Check the white cylinder fuel filter by the VRO pump on the left side of the motor. If it gets junk inside it will cause a check engine light.
06-14-2021, 05:34 AM
Replies: 42
Views: 1,144
Posted By wstanford277

Go to a mustang 5.0 site and look. You’ll find...

Go to a mustang 5.0 site and look. You’ll find anything from stock to 600+ hp out of a 302. A Cam and carb swap will be the cheapest/easiest hp you can add.
06-13-2021, 05:29 PM
Replies: 8
Views: 381
Posted By wstanford277

Check the main ground wire eyelet that bolts to...

Check the main ground wire eyelet that bolts to the block to the right of the starter for corrosion.
06-13-2021, 04:32 PM
Replies: 8
Views: 381
Posted By wstanford277

Does it have Yamaha f150s?

Does it have Yamaha f150s?
06-13-2021, 08:36 AM
Replies: 34
Views: 1,144
Posted By wstanford277

I use the turnpike when driving from Atlanta. ...

I use the turnpike when driving from Atlanta. I’d go I10-I75-turnpike. Avoid Orlando and Miami during rush hours. Avoid crossing over to key largo on Saturday. Early morning or close to dark is...
06-12-2021, 04:13 AM
Replies: 288
Views: 17,306
Posted By wstanford277

Planned a weekend guys trip to Panama City after...

Planned a weekend guys trip to Panama City after seeing the forecast a week ago. As usual the forecast changed and was wrong. We got beat up running out to get a 6 man limit. One of the greenhorns...
06-09-2021, 10:18 AM
Replies: 9
Views: 370
Posted By wstanford277

Timing belts are tough. Most will last longer...

Timing belts are tough. Most will last longer than the replacement maintenance schedule. If the belt has a manufacturing defect it breaks or fails with little use. For a belt to fray it’s an...
06-07-2021, 11:23 AM
Replies: 9
Views: 370
Posted By wstanford277

Inspect the new belt for fraying/rubbing after...

Inspect the new belt for fraying/rubbing after running the engine the first time. They same source could get the 2nd belt.
06-06-2021, 08:12 AM
Replies: 288
Views: 17,306
Posted By wstanford277

Drop 1/2 way down.

Drop 1/2 way down.
Forum: Gulf Coast
06-06-2021, 08:09 AM
Replies: 14
Views: 964
Posted By wstanford277

If you don’t see the structure move one. Try...

If you don’t see the structure move one. Try live bait or fresh not frozen bait. Cut Bonita works well. Lighter floro leaders and smaller weights help.
06-06-2021, 07:11 AM
Replies: 46
Views: 1,975
Posted By wstanford277

It takes some serious eagle eyes to spot a .5 mm...

It takes some serious eagle eyes to spot a .5 mm hole on an unfinished block. The hole would be the size of the tip of a toothpick.

...
06-05-2021, 03:40 PM
Replies: 46
Views: 1,975
Posted By wstanford277

JB should work if you just clean off the oil...

JB should work if you just clean off the oil residue. I bet you could stick a toothpick in the hole and snap it off flush to plug it.
06-05-2021, 12:24 PM
Replies: 46
Views: 1,975
Posted By wstanford277

Run it and add oil each trip.

Run it and add oil each trip.
06-05-2021, 11:00 AM
Replies: 20
Views: 982
Posted By wstanford277

Tighten it back up.

Tighten it back up.
06-05-2021, 06:26 AM
Replies: 87
Views: 1,467
Posted By wstanford277

Yes. Light coat will show where any liquid is...

Yes. Light coat will show where any liquid is coming from.
06-03-2021, 08:19 PM
Replies: 5
Views: 226
Posted By wstanford277

Based on the rpm/speed it sounds like your...

Based on the rpm/speed it sounds like your current prop is a 17” pitch. Look on the hub for any characters and post a picture of your prop.
06-03-2021, 07:24 PM
Replies: 87
Views: 1,467
Posted By wstanford277

If you think the VRO or oil line has a leak use...

If you think the VRO or oil line has a leak use talcum powder or flour on both to find it. That’s the only way I found the small crack on the back side of my VRO.
06-03-2021, 04:36 PM
Replies: 9
Views: 302
Posted By wstanford277

The ground corrosion is a common issue on F150s...

The ground corrosion is a common issue on F150s and causes all kinds of intermittent gremlins. I’d start there any then follow the starter/solenoid diagnostics.
06-03-2021, 03:17 PM
Replies: 9
Views: 302
Posted By wstanford277

What failed?

What failed?
06-03-2021, 02:06 PM
Replies: 7
Views: 512
Posted By wstanford277

Try Uncle Ernie's in PC for lunch or dinner. ...

Try Uncle Ernie's in PC for lunch or dinner. Plenty of dock space.
06-03-2021, 01:31 PM
Replies: 8
Views: 751
Posted By wstanford277

I have 4 torium 16s and bought 2 speedmaster 16s...

I have 4 torium 16s and bought 2 speedmaster 16s 1.5 years ago. I’ll never buy another torium. The low gear on the speedmaster is great for winching.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.