Notices
 
Search: Posts Made By: scubasniper2009
Showing results 1 to 25 of 92
Search took 0.08 seconds.
06-11-2019, 09:59 AM
Replies: 11
Views: 539
Posted By scubasniper2009

Thanks FWpratt, that is exactly what I needed....

Thanks FWpratt, that is exactly what I needed. Unfortunately, that leaves me with no idea as to what is wrong.

As as far as the brushes go, I only needed 2. Problem is that one (the $95 one) had...
06-11-2019, 08:56 AM
Replies: 11
Views: 539
Posted By scubasniper2009

I double checked the up relief valve and...

I double checked the up relief valve and everything is put back like the drawing. Sure of that. I am not sure if there is supposed to be a check ball inside the filter valve or what size it might be....
06-10-2019, 07:55 PM
Replies: 11
Views: 539
Posted By scubasniper2009

Yamaha Tilt and Trim Rebuild Issues

Yamaha F150 (2005). I took apart my tilt and trim unit because the oil level kept dropping over time. When I pulled the motor apart, stinky gray hydraulic oil/ carbon dust went everywhere. Had to...
06-23-2016, 02:44 PM
Replies: 18
Views: 9,177
Posted By scubasniper2009

I torqued it to the FSM spec. Not sure why this...

I torqued it to the FSM spec. Not sure why this one failed. I stopped by the local Yamaha dealer today. They had a dozen in stock so i grabbed a couple pairs. Not a big deal, just wanted to make...
06-22-2016, 08:00 PM
Replies: 18
Views: 9,177
Posted By scubasniper2009

Yamaha F150 New Lower Unit Drain Plug Gasket Failure

I recently completed my annual maintenance and, in that course of action, changed my lower unit oil. As usual, I used brand new OEM gaskets (Part # 90430-08003-00) for the drain and vent plugs....
04-03-2015, 10:36 PM
Replies: 21
Views: 3,679
Posted By scubasniper2009

Last time I did work on my fuel system, I had a...

Last time I did work on my fuel system, I had a similar problem. Ran fine for hours at lower RPM ranges and then would sputter after sitting at WOT for about 15 seconds. Ended up being the fuel...
03-23-2015, 05:24 PM
Replies: 10
Views: 874
Posted By scubasniper2009

My 2005 had a failing balancer assembly. It...

My 2005 had a failing balancer assembly. It whines for a while before she finally lets go. There are some very well written instructions on the forum about how to change them. A couple of hours and a...
03-04-2015, 04:20 PM
Replies: 32
Views: 3,698
Posted By scubasniper2009

I used to have a cheap danforth. It would have...

I used to have a cheap danforth. It would have problems all the time. Bought a Manson Supreme and have had instant strong hookups. Like night and day. 5 times the cost but 100 percent satisfaction....
09-05-2014, 09:06 PM
Replies: 63
Views: 6,070
Posted By scubasniper2009

A cruise ship outta do... All boats rock. a...

A cruise ship outta do... All boats rock. a little dramamine goes a long way and over time, you may get used to the rocking.
09-05-2014, 09:02 PM
Replies: 17
Views: 1,062
Posted By scubasniper2009

I recently purchased a 10lb Manson Supreme for my...

I recently purchased a 10lb Manson Supreme for my boat from Defender.com. It held extremely well on sandy bottom. I did have a hard time getting it up and had to use the anchor ball retrieval method....
09-01-2014, 11:38 AM
Replies: 7
Views: 613
Posted By scubasniper2009

I use a 2x4 to take the load off the tilt and...

I use a 2x4 to take the load off the tilt and trim rams.
08-24-2014, 07:10 PM
Replies: 2
Views: 442
Posted By scubasniper2009

I took a closer look at it and the riveted shaft...

I took a closer look at it and the riveted shaft looks bent. It is causing the latch to drag along the floor plate as it open. Rather than send it back, I think I am going to drill out and replace...
08-24-2014, 05:43 PM
Replies: 2
Views: 442
Posted By scubasniper2009

Anchor tensioner range of motion

I am installing an anchor roller and subsequently, an anchor chain tensioner. My tensioner is like the one in the photo.

http://www.bottompaintstore.com/images/36227.gif

The tensioner will only...
08-21-2014, 09:13 PM
Replies: 207
Views: 7,445
Posted By scubasniper2009

This one time at fish camp...I won a new wash...

This one time at fish camp...I won a new wash down pump!
08-21-2014, 09:12 PM
Replies: 207
Views: 7,445
Posted By scubasniper2009

This one time at fish camp...Wait... I have never...

This one time at fish camp...Wait... I have never been to fish camp?!
08-21-2014, 08:49 PM
Replies: 888
Views: 103,617
Posted By scubasniper2009

This thread is awesome! OP, Hope you get fully...

This thread is awesome! OP, Hope you get fully compensated for the thief's actions and are made whole. This dealer is a fool. If I spent $65K for a brand new boat I would expect a boat in new...
08-20-2014, 08:09 PM
Replies: 10
Views: 837
Posted By scubasniper2009

The Works toilet bowl cleaner. $1.50 at wal-mart.

The Works toilet bowl cleaner. $1.50 at wal-mart.
08-15-2014, 07:36 AM
Replies: 17
Views: 901
Posted By scubasniper2009

I need a new anchor too. I have been looking at...

I need a new anchor too. I have been looking at the Manson Supreme anchors. They look like they work well. I had a cheap $20 anchor from Bass Pro and it had a hard time holding bottom and has bent...
08-15-2014, 06:51 AM
08-15-2014, 06:49 AM
08-04-2014, 03:04 PM
Replies: 5,669
Views: 675,476
Posted By scubasniper2009

Went out and caught our limit of scallops, shot a...

Went out and caught our limit of scallops, shot a flounder, and pulled in a half a dozen blue crabs. Overall, a pretty good day!
08-04-2014, 04:36 AM
Replies: 11
Views: 760
Posted By scubasniper2009

the Works toilet bowl cleaner. $1.50 at Wal-Mart

the Works toilet bowl cleaner. $1.50 at Wal-Mart
08-01-2014, 12:15 AM
Replies: 91
Views: 5,195
Posted By scubasniper2009

Exactly my thoughts. After the trip, if you feel...

Exactly my thoughts. After the trip, if you feel like you want to help with the gas bill, your name moves right to the top of the call list for the next fishing trip. I usually ask one fishing buddy...
07-30-2014, 11:23 AM
Replies: 23
Views: 1,982
Posted By scubasniper2009

I have used these from Amazon. If you can solder...

I have used these from Amazon. If you can solder and use heat shrink, it will save you hundreds vs the marine stores. I used it in all my hatches and couldn't be happier. They are bright and come in...
07-30-2014, 11:15 AM
Replies: 46
Views: 3,733
Posted By scubasniper2009

Actually, the marine store around here sells them...

Actually, the marine store around here sells them in stainless. They work but not as clean as staples.
Showing results 1 to 25 of 92
 


 
Forum Jump