The Hull Truth - Boating and Fishing Forum - View Profile: Backcove26

Notices

Backcove26 Backcove26 is offline

Senior Member

About Me

  • About Backcove26
    Country of Residence
    US
    Gender
    Male
  • Signature

Statistics

Total Posts
Albums
Visitor Messages
Total Likes
General Information
  • Last Activity: 03-28-2020 02:06 PM
  • Join Date: 03-26-2016
  • Referrals: 0

Friends

Showing Friends 1 to 1 of 1

Visitor Messages

Showing Visitor Messages 1 to 2 of 2
  1. 04-29-2019 06:56 PM
    Thanks for the advice broher
  2. 04-29-2019 06:47 PM
    Hey Backcove, That was probably the most pain-staking part of the job because I would lay the fiberglass and wrap the cloth over the edge but had to tack it with push pins while it dried and then flip the top and overlap it on the other side. I took my time since the edge is the most vulnerable to getting hit and I wanted to be sure that it was well covered.

    The biggest issue was that I used Lowe's EPS or EXS (I can't remember which) and it was stamped with blue ink which separated from the polystyrene and had to be patched. Had I known, I would have sanded the ink off before I started. Everything else held really well and it saved tons of money as opposed to having one vacuum bagged to fit the arc of my frame.

    Good luck, I think it's worth the effort.

    Randy

Likes Received

65 Likes
  1. Unevensteven liked post by Backcove26 On thread : Prop Help 2019 Parker 2520XLD twin 200XCA
  2. clamc liked post by Backcove26 On thread : Twin Yam 200's; Power steering needed?
  3. 6104696 liked post by Backcove26 On thread : Twin Yam 200's; Power steering needed?
  4. Chris Craft Cutlass liked post by Backcove26 On thread : Small block Chevy electronic ignition
  5. clv liked post by Backcove26 On thread : Yamaha Saltwater Series II Props - $500
    Props in the pictures are definitely SDS
    Liked On: 12-19-2019, 05:48 AM
    Posted On: 12-19-2019, 04:41 AM
  6. mheltun liked post by Backcove26 On thread : Uflex hydraulic steering problem
    Uflex steering is good stuff, customer support is excellent. I would buy it again.
    Liked On: 11-29-2019, 06:52 PM
    Posted On: 11-29-2019, 10:22 AM
  7. mheltun liked post by Backcove26 On thread : Uflex steering question
  8. mheltun liked post by Backcove26 On thread : Uflex steering question
    Must be air, mine is smooth as silk lock to lock.
    Liked On: 08-25-2019, 04:50 PM
    Posted On: 08-25-2019, 12:31 PM
  9. Chris Craft Cutlass liked post by Backcove26 On thread : 1979 Chris Craft engine mounts parts new or used ?
  10. PhinChaser liked post by Backcove26 On thread : New 300 Yamaha overheats on muffs
    That will damage the water pump.
    Liked On: 06-19-2019, 08:41 AM
    Posted On: 06-17-2019, 04:00 PM
  11. Gatorzone19 liked post by Backcove26 On thread : New 300 Yamaha overheats on muffs
    Thats normal. Run it in a plastic tub and it wont happen. They dont like running on muffs.
    Liked On: 06-18-2019, 06:13 AM
    Posted On: 06-17-2019, 03:15 PM
  12. BCPD199 liked post by Backcove26 On thread : Trim tab question
    Its working as it should.
    Liked On: 05-13-2019, 12:00 PM
    Posted On: 05-13-2019, 10:39 AM
  13. popeyeiii liked post by Backcove26 On thread : Trim tab question
    Its working as it should.
    Liked On: 05-13-2019, 11:24 AM
    Posted On: 05-13-2019, 10:39 AM
  14. macabear liked post by Backcove26 On thread : Marina refusing to release boat to me, is this legal?
  15. N747JB liked post by Backcove26 On thread : Marina refusing to release boat to me, is this legal?

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.