The Hull Truth - Boating and Fishing Forum - View Profile: Backcove26

Notices

Backcove26 Backcove26 is offline

Senior Member

About Me

  • About Backcove26
    Country of Residence
    US
    Gender
    Male
  • Signature

Statistics

Total Posts
Albums
Visitor Messages
Total Likes
General Information
  • Last Activity: 04-24-2020 11:03 AM
  • Join Date: 03-26-2016
  • Referrals: 0

Friends

Showing Friends 1 to 1 of 1

Visitor Messages

Showing Visitor Messages 1 to 2 of 2
  1. 04-29-2019 06:56 PM
    Thanks for the advice broher
  2. 04-29-2019 06:47 PM
    Hey Backcove, That was probably the most pain-staking part of the job because I would lay the fiberglass and wrap the cloth over the edge but had to tack it with push pins while it dried and then flip the top and overlap it on the other side. I took my time since the edge is the most vulnerable to getting hit and I wanted to be sure that it was well covered.

    The biggest issue was that I used Lowe's EPS or EXS (I can't remember which) and it was stamped with blue ink which separated from the polystyrene and had to be patched. Had I known, I would have sanded the ink off before I started. Everything else held really well and it saved tons of money as opposed to having one vacuum bagged to fit the arc of my frame.

    Good luck, I think it's worth the effort.

    Randy

Likes Given

89 Likes
  1. Backcove26 liked post by Tom W Clark On thread : Teleflex NFB Steering Slop?
  2. Backcove26 liked post by cj8mule On thread : Electrical wiring nightmare question......
  3. Backcove26 liked post by Cooper On thread : Can a new 38 Fountain handle 6-8' choppy seas on the nose (Video)
  4. Backcove26 liked post by Raybo Marine NY On thread : How much should this job cost?
  5. Backcove26 liked post by Raybo Marine NY On thread : Do shops add fuel to a boat before sea trialing?
  6. Backcove26 liked post by Lone Ranger On thread : Ideas on 2018 Intrepid 327 electrical issue?
    Sounds like a Feed or Ground to a Main Panel to the Console area .
    Liked On: 11-29-2019, 10:13 AM
    Posted On: 11-28-2019, 06:21 AM
  7. Backcove26 liked post by Tom W Clark On thread : Boat Part ID and Locate
  8. Backcove26 liked post by Tom W Clark On thread : Boat Part ID and Locate
  9. Backcove26 liked post by Raybo Marine NY On thread : Engine mount lag repair didn't even last one boat ride?
  10. Backcove26 liked post by jlpjr On thread : 350 Long block
  11. Backcove26 liked post by Raybo Marine NY On thread : best exterior boat caulk
    not me , the 4000 was junk
    Liked On: 11-06-2019, 03:39 AM
    Posted On: 11-05-2019, 02:04 PM
  12. Backcove26 liked post by Raybo Marine NY On thread : Anyone heard of this outboard seller
  13. Backcove26 liked post by PeteH On thread : Uflex hydraulic steering problem
    Sounds like prop torque. Motor too low. Trim anode incorrectly positioned.
    Liked On: 10-21-2019, 03:33 AM
    Posted On: 10-21-2019, 02:59 AM
  14. Backcove26 liked post by Raybo Marine NY On thread : Heard sea hunt being sold..
    ah yes- the bubble thats been popping for the last few years
    Liked On: 10-10-2019, 03:16 AM
    Posted On: 10-09-2019, 10:15 AM
  15. Backcove26 liked post by 47Fountain On thread : 8 hours labor to ADJUST shift cables.....

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.