2LikesTool Box rod holder! New and Imporved!
02-28-2014, 08:45 AM
#1
Admirals Club 
THT sponsorThread Starter
Join Date: Feb 2011
Location: Lexington SC
Posts: 890
Tool Box rod holder! Free Shipping Fathers day special
THT special at 250.00 for the 7 rod holder mount, Anodized or Powder coating same price on ALL!!!!!
The 9 holder @ 300.00
The 11 holder @ 350.00
These racks are built with quality tulip rod holders with the new and improved super durable insert. No more worries of fading or mildew stains to junk up your white inserts. Also you will see a concept on this rod holder referred to as blind fastening. Once mounted, you will see no mounting screws as it only requires one hole drilled in your box compared to other mounting pads requiring 4. Not only does this concept give a "cleaner" look, it also makes it very difficult to for a thief to take while your off shore fishing for the day.
These racks are powder coated with in a super durable Black or White finish and they are ready to be shipped to your door. Other colors available upon request with a slight up charge as well as an anodized aluminum finish.
Shipping on the east coast is around 30.00 and increases a little as they pass they Mississippi.
This rack is built at 57 1/2 inches wide which a common size for most full sized tool boxes. The can be built larger/smaller as needed.
These racks use a custom "blind fasten" pad that not only allows for a clean look, but keeps you with only one mounting hole.
The interior finish washer and bolt (supplied)
Not only do you get the custom mounting pads, you also receive the custom inserts that are specifically made for these racks. These "hard plastic" inserts not only repels mildew but also protects the rim of the rod holder with an overlap lip. These inserts are custom made in Good ole Tennessee
Here are few pictures of the racks and the powder coating process
These powder coated racks are sprayed with an acid wash and also blasted with a new Hydro Blaster to ensure optimal bond
After spraying, each part is placed in the oven where each batch Is recorded for quality assurance
Here is a quick look at the machine shop where all the components are manf
The 9 holder @ 300.00
The 11 holder @ 350.00
These racks are built with quality tulip rod holders with the new and improved super durable insert. No more worries of fading or mildew stains to junk up your white inserts. Also you will see a concept on this rod holder referred to as blind fastening. Once mounted, you will see no mounting screws as it only requires one hole drilled in your box compared to other mounting pads requiring 4. Not only does this concept give a "cleaner" look, it also makes it very difficult to for a thief to take while your off shore fishing for the day.
These racks are powder coated with in a super durable Black or White finish and they are ready to be shipped to your door. Other colors available upon request with a slight up charge as well as an anodized aluminum finish.
Shipping on the east coast is around 30.00 and increases a little as they pass they Mississippi.
This rack is built at 57 1/2 inches wide which a common size for most full sized tool boxes. The can be built larger/smaller as needed.
These racks use a custom "blind fasten" pad that not only allows for a clean look, but keeps you with only one mounting hole.
The interior finish washer and bolt (supplied)
Not only do you get the custom mounting pads, you also receive the custom inserts that are specifically made for these racks. These "hard plastic" inserts not only repels mildew but also protects the rim of the rod holder with an overlap lip. These inserts are custom made in Good ole Tennessee
Here are few pictures of the racks and the powder coating process
These powder coated racks are sprayed with an acid wash and also blasted with a new Hydro Blaster to ensure optimal bond
After spraying, each part is placed in the oven where each batch Is recorded for quality assurance
Here is a quick look at the machine shop where all the components are manf
Last edited by PalmettoTrooper; 06-09-2016 at 07:23 AM.
02-28-2014, 01:11 PM
#2
Admirals Club
Join Date: Sep 2013
Location: NE Alababa
Posts: 400
Hey Trooper. I like that mount. Alot. Fewer holes = fewer places to leak!
I assume you can still do that one with alternating straight to angled tulips and accomodate more rods, like the 11 rod unit we discussed last week. Correct?
Looks good man. Be ordering soon.
David
I assume you can still do that one with alternating straight to angled tulips and accomodate more rods, like the 11 rod unit we discussed last week. Correct?
Looks good man. Be ordering soon.
David
02-28-2014, 03:25 PM
#6
Admirals Club
THT sponsorThread Starter
Join Date: Feb 2011
Location: Lexington SC
Posts: 890
360.00 for the 11
Jagsare1: Im mounting a white one in the next few days and will take a pic of it loaded down with heavy tackle
Same concept being used on the new Hydrosport 4200SF. Take the virtual tour and check it out
http://vt.prestigevision.com/hydrasp...347/embed.html
Jagsare1: Im mounting a white one in the next few days and will take a pic of it loaded down with heavy tackle
Same concept being used on the new Hydrosport 4200SF. Take the virtual tour and check it out
http://vt.prestigevision.com/hydrasp...347/embed.html
02-28-2014, 06:36 PM
#8
Admirals Club
THT sponsorThread Starter
Join Date: Feb 2011
Location: Lexington SC
Posts: 890
Hey Stamas, I have a full time career and do this as a hobby. I do everything by myself and truly enjoy seeing things come together. With that, I'm able to offer products just a little over cost. This hobby allows me to keep my boats operational on a Troopers salary!
02-28-2014, 06:53 PM
#9
Senior Member
Join Date: Oct 2010
Location: Sarasota
Posts: 3,541
I love to see someone take a Idea, apply some creativity and talent and put together something that looks this good with a great function at a very fair price.
Tig welders, Argon, materials, electricity and powdercoating are not cheap.
A small fabrication business, making money.
.
Good luck to you.
Whats the next product?
Tig welders, Argon, materials, electricity and powdercoating are not cheap.
A small fabrication business, making money.
.Good luck to you.
Whats the next product?
03-01-2014, 03:00 PM
#13
Admirals Club
THT sponsorThread Starter
Join Date: Feb 2011
Location: Lexington SC
Posts: 890
The one in my pic is the mother ship. I've built a few since. I'll tell ya, it all depends on the grill you want..
Heres some new photos on a customers truck
Jagsare1: The customer didn't have any large tackle to put in the rod rack so I stood on it to show its strength and durability. I'm 270lbs and balanced on it for a few minutes with out a hitch
Heres some new photos on a customers truck
Jagsare1: The customer didn't have any large tackle to put in the rod rack so I stood on it to show its strength and durability. I'm 270lbs and balanced on it for a few minutes with out a hitch
03-01-2014, 05:11 PM
#15
Admirals Club
Join Date: Aug 2012
Posts: 913
I want the 11 rod holder shipped, all in black, can u LineX it before??
Shipping to 78043
Thx
Email is Jimlottusmc@yahoo.com
Shipping to 78043
Thx
Email is Jimlottusmc@yahoo.com
03-02-2014, 04:31 AM
#16
Senior Member
Join Date: Jan 2009
Location: NJ
Posts: 643
Trooper: I love the 11-rod holder. I already have a rack for the truck, but I need to replace the factory rocket launcher on my Parker 2520.
If I unbolted it and shipped it to you, do you think it would be possible for you to make an 11-rod launcher with the same anchor points as my factory launcher?
If I unbolted it and shipped it to you, do you think it would be possible for you to make an 11-rod launcher with the same anchor points as my factory launcher?
