The Hull Truth - Boating and Fishing Forum

The Hull Truth - Boating and Fishing Forum (https://www.thehulltruth.com/index.php)
-   The Boating Forum (https://www.thehulltruth.com/boating-forum-14/)
-   -   Downeaster boat project (https://www.thehulltruth.com/boating-forum/634828-downeaster-boat-project.html)

HTJ 01-19-2016 03:18 PM


Originally Posted by surv (Post 7316525)
I bought the boat for the transom bracket and motor. The blue and white boat in the background of the third picture is what i plan on using it for.


Please deliver said unwanted hull to Baytown TX, will provide BBQ and beer for the evening, and maybe $20 in gas money if you don't drink too much.


Very nice lines, I would have to keep it.

HTJ 01-19-2016 03:20 PM

[QUOTE=surv;7317175]I'm not really looking for two projects, this one was supposed to be so I could put the other one together. Now that I have the Downeaster I don't want to junk it. What to do??[/QUOTE]


Please deliver said unwanted hull to Baytown TX, will provide BBQ and beer for the evening, and maybe $20 in gas money if you don't drink too much.


Very nice lines, I would have to keep it.

HTJ 01-19-2016 03:23 PM

[QUOTE=surv;7317175]I was told by the man I bought it from that his brother in-law ordered this boat new and had them build it with a full transom and bracket.

I'm not really looking for two projects, this one was supposed to be so I could put the other one together. Now that I have the Downeaster I don't want to junk it. What to do??[/QUOTE]


Please deliver said unwanted hull to Baytown TX, will provide BBQ and beer for the evening, and maybe $20 in gas money if you don't drink too much.


Very nice lines, I would have to keep it.

sawfish7 01-19-2016 04:03 PM

Downeaster boat prodject
 
I bought a 17 in 88. Made by Kieth Willis of Marshalberg. 100% hand laid. A lot of them especially the 25s were used by commercial fishermen. Tough as nails! Bumpy wet ride but would go anywhere. Had 12 fun years in that boat and was in great shape when I sold it. Good luck with the restore!

81Malibu 01-19-2016 04:53 PM

Subscribed.

surv 01-19-2016 05:28 PM

2 Attachment(s)
Thanks for all the support everyone!

When I said quick and dirty I didn't mean poor quality. I plan on building it with good materials and sound construction methods, I just want to get a good turn over time on it and not spend to much time fairing and finishing an old fishing boat.

I haven't decided on the stringers but the deck will be marine ply with glass on both sides. Then a good quality topside paint rolled and or brushed with some non skid on the decks.

I would like to hear anyone's suggestions on stringer construction.

Yesterday I cleaned it out. It didn't take long because it was so rotten, sure was a lot easier than tearing one apart that's still solid.

surv 01-21-2016 04:15 PM

What do you all think about the transom bracket?

I'm considering notching the transom for a 25"shaft and building in a splash well. I like a full closed transom but don't know how its going to act on a 19' boat.

surv 01-21-2016 04:19 PM


Originally Posted by HTJ (Post 8625904)
Please deliver said unwanted hull to Baytown TX, will provide BBQ and beer for the evening, and maybe $20 in gas money if you don't drink too much.


Very nice lines, I would have to keep it.

The BBQ and beer sounds good but now this extra hull is going to replace my primary boat. :thumbsup:

mattsmall1972 01-22-2016 09:38 AM

I don't know why you would want to lose deck space by notching the transom. If the bracket is in good shape, definitely keep it IMO. Didn't you buy the boat because of the bracket?

surv 01-22-2016 04:27 PM


Originally Posted by mattsmall1972 (Post 8635031)
I don't know why you would want to lose deck space by notching the transom. If the bracket is in good shape, definitely keep it IMO. Didn't you buy the boat because of the bracket?

I bought it to rob the bracket for a different boat.

I don't know how it will effect the boat. It just seems like having a 24" setback on a 18' 3" boat may have a negative effect on it.;?

surv 02-02-2016 11:05 AM

2 Attachment(s)
Here are a few picks of the molds for fiberglass stringers. They are 6" wide at the top, 10" wide at the bottom and app 11" high. I have a few more pieces to make then take them out of the boat and cover them with fiberglass.

Its unreal how much faster it is to build them like this. I spent a little more than a year on my Anacapri to get the stringers in and they still aren't finished. Two good afternoons and these are already about to shape.

Once I get them fiberglassed and pop them off the mold ill tab them in, or cover them completely depending on how ridged they are, then fill them with polyurethane foam.

murfpcola 02-02-2016 11:43 AM

Wow! Looking good. Keep the pictures coming.

surv 02-07-2016 08:49 AM

4 Attachment(s)
Starting to take spape.

I need to build the bulkheads from the stringers out to the chine but I think ill have to after I get the permanent structure made and put back in. Without removing the cap I dont think I can pick it up with the side bulkheads built.

The fuel tank is 25 gal, it came with the boat. I would like to have about 40 but I think it will be fine. This is a bay boat not offshore, thoughts?

twitch 02-07-2016 10:07 AM

If you are gonna use a carbed 2 stroke for power, I'd look for a 40-60 gallon tank.

ChiefD 02-07-2016 10:44 AM

Very nice work on the stringer molds surv!

I like the nice wide footprint at the base where stringers meet the hull. With this type of system what is the recommended laminate thickness?

You got me thinking......maybe I should go this route on my project. I could lay those up with ISO then tab in with epoxy. This would minimize the expensive epoxy and marine ply I had planned.....hmmmm
D

surv 02-07-2016 01:48 PM


Originally Posted by twitch (Post 8689664)
If you are gonna use a carbed 2 stroke for power, I'd look for a 40-60 gallon tank.

I'm going to use the Johnson 130 that was on it. I was estimating 2 mpg so approximately 50 mile range. Does that sound like its in the ball park?

surv 02-07-2016 01:57 PM


Originally Posted by ChiefD (Post 8689790)
Very nice work on the stringer molds surv!

I like the nice wide footprint at the base where stringers meet the hull. With this type of system what is the recommended laminate thickness?

You got me thinking......maybe I should go this route on my project. I could lay those up with ISO then tab in with epoxy. This would minimize the expensive epoxy and marine ply I had planned.....hmmmm
D

Thanks CheifD,
I have been following your build, nice work. I'm glad you found my project.

I'm planning on using 12 oz uni-glass and mat to build up a thickness of about 3/8" thick. Then tab them in with a few layers of woven roven and mat. To be honest with you I don't know how thick they need to be just shooting off the hip a little bit. If they feels flimsy then ill add more glass. I'll also pour them full of foam so that should make them more ridged.

I have an old Skeeter with similar construction and it doesn't have more than 1/4" thick glass on the stringers so I think 3/8" will be plenty thick.

twitch 02-07-2016 03:14 PM

2 mpg is a probably close. I had a 140 omc 2 stroke on a 21 privateer for years and got a little better fuel burn than that. I had a 60 ish gallon capacity and never once wished for less capacity. I think a 25 gallon tank would eliminate a lot of potential fishing trips unless you carried extra fuel on the deck.

What area of the country will it be fished?

H2OBUG 02-07-2016 03:20 PM

That old big block V-4 Johnson will roll. Rework her and name her Alexis just for kicks.

surv 02-07-2016 05:25 PM


Originally Posted by twitch (Post 8690634)
2 mpg is a probably close. I had a 140 omc 2 stroke on a 21 privateer for years and got a little better fuel burn than that. I had a 60 ish gallon capacity and never once wished for less capacity. I think a 25 gallon tank would eliminate a lot of potential fishing trips unless you carried extra fuel on the deck.

What area of the country will it be fished?

The NC coast, mainly around Wilmington or Morehead city.


All times are GMT -7. The time now is 05:29 PM.

Powered by vBulletin® Version 3.9.3.8
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.