hook79
03-17-2010, 08:55 PM
homemade rodholder for truck bed, need help my rods depend on it...
SportFishing and Charters Forum - homemade
THE HULL TRUTH is the world's largest FREE network for the discussion of Boating & Fishing. Whether you're researching a new boat, or are a seasoned Captain, you'll find The Hull Truth Boating & Fishing Message Forum contains a wealth of information from Boaters and Sportfishermen around the world.
View Full Version : homemade
jtburf
03-18-2010, 03:34 AM
see below
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34497-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34496-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34495-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34494-a.jpg
John
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34497-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34496-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34495-a.jpg
http://www.thehulltruth.com/members/jtburf-albums-marti-cora-picture34494-a.jpg
John
gtrfred
03-18-2010, 07:28 AM
jt burf
looks very good. is the board just slipped over the top of the rear wall of the bed? Or is it held in with some kind of fastener?
looks very good. is the board just slipped over the top of the rear wall of the bed? Or is it held in with some kind of fastener?
rarebreed
03-18-2010, 10:56 AM
Attached to tool box with 2 carraige bolts with wing nuts. Weighs about 20 lbs and takes 2 minutes to put in or take off. Cost about $25.
Maclin
Maclin
joemat
03-18-2010, 11:09 AM
homemade rodholder for truck bed, need help my rods depend on it...
Your in NJ. Go see Norm at Norms Welding in Lanoka Harbor. Why mess with wood.
Norm built mine custom and it did not cost much.
Your in NJ. Go see Norm at Norms Welding in Lanoka Harbor. Why mess with wood.
Norm built mine custom and it did not cost much.
TimW Texas
03-18-2010, 11:19 AM
Wow that is some great ideas
jtburf
03-18-2010, 11:22 AM
jt burf
looks very good. is the board just slipped over the top of the rear wall of the bed? Or is it held in with some kind of fastener?
Just slips over and i used a small ratchet strap to secure it.
Cannot remember what it cost but was not bad, and even 7' rods never had an issue with low overhangs.
John
looks very good. is the board just slipped over the top of the rear wall of the bed? Or is it held in with some kind of fastener?
Just slips over and i used a small ratchet strap to secure it.
Cannot remember what it cost but was not bad, and even 7' rods never had an issue with low overhangs.
John
Ice Cream Man
03-18-2010, 12:41 PM
This is what I use - no more broken rods ......... ICM
REDWEISER
03-18-2010, 02:45 PM
My old one's still holding up pretty good.
http://img512.imageshack.us/img512/9421/picture248.jpg
http://img512.imageshack.us/img512/9421/picture248.jpg